What Is Viscosity Index and Why Does It Matter in Engine Oil?
Engine Oil Insights & Industry Updates

What Is Viscosity Index and Why Does It Matter in Engine Oil?

Viscosity index is one of the few numbers on an engine oil data sheet that describes behaviour rather than a test result. It says how much the oil’s viscosity changes between low and high temperature. A high figure means the oil stays closer to its designed thickness, which is what a multigrade oil is for. A low figure means it thins quickly when hot and thickens sharply when cold.

Viscosity index is calculated from kinematic viscosity measured at 40 and 100 degrees Celsius using ASTM D2270. The calculation compares the oil with two reference oils that bracket the behaviour: one that thins quickly with heat and one that thins slowly. A higher number means a flatter viscosity curve between those two temperatures.

Because it is derived from two measurements, the index is not an independent property that can be improved at will. It summarises composition and additives, and it can be raised by using base oils that are naturally flat in behaviour, or by adding viscosity index improvers, or both.

The base oil family sets the starting point. Conventional Group I base oils, still common in low-cost products, usually sit in the nineties to around one hundred. Group II, the modern conventional, lands somewhat higher. Group III, the hydrocracked base oil in most synthetic products sold today, commonly reaches the one hundred and twenties. Fully synthetic PAO base oils can sit well above that.

This is why a synthetic can carry the same grade as a mineral product and still behave better in the cold, without either being mislabelled. The grade is a promise at two defined temperatures; the index describes the shape of the curve between them and beyond.

Adding an improver lets a formulator build a multigrade from a lighter base oil. The polymer expands as it heats, so the blend thickens at high temperature and stays pumpable at low temperature. That is how a 5W-30 is built from components that would otherwise be too thin at the top and too thick at the bottom.

The catch is shear. These polymers are long molecules, and in a gear train, a high-pressure pump or a bearing they can be cut into shorter pieces. When that happens the oil permanently loses some thickening effect, and the grade on the label is no longer the grade in service. That is why shear stability is tested after mechanical shear rather than assumed from a fresh sample.

A very high index achieved mainly with polymer is therefore a purchasing risk rather than a benefit. The question is not how high the index is, but how much survives shear and whether the product stays in grade after the required test.

A flatter curve keeps the oil pumpable at the temperatures a cold start produces and lets it reach bearings faster, which shortens the period of boundary lubrication. It also holds the grade in a hot sump, so idle oil pressure stays where the engine expects it, and it allows a lower viscosity grade without losing high-temperature protection, which is the mechanism behind most fuel-economy claims.

Data pointTestWhat good looks likeWhy the buyer should care
Kinematic viscosity at 40 and 100 degrees CASTM D445Inside the grade band with margin at both endsConfirms the grade is real, not just printed
Viscosity indexASTM D2270Consistent with the base oil group claimedA figure far above the base oil family suggests polymer, which raises the shear question
HTHS viscosityASTM D4741 or D5481Inside the band its category requiresThe number that protects a bearing at operating temperature
Shear stabilityASTM D6278 or D7109, or the sequence testStays in grade after shearSeparates a durable multigrade from one that thins in service
Cold cranking and pumpabilityASTM D5293 and D4684Meets the W number claimedThe winter number is a test result, not a description

If-then: if two oils in the same grade carry very different indexes, then the higher figure is not automatically the better product, and the shear result decides which one holds its grade in service. If the application is a hot-climate fleet at sustained load, then HTHS and oxidation resistance matter more than the index. If the application is cold-start duty, then the index and the cold cranking figure together decide whether the engine starts.

Comparing viscosity index claims across suppliers and need the batch data behind the number, including shear stability and HTHS? Send the grades you are evaluating and the application, and we will return the full data set rather than the figure on the label.

Is a higher viscosity index always better?

Not always. A very high index built with a large polymer dose can shear down in service, after which the product behaves like a thinner oil than its label. Compare index plus shear stability plus HTHS.

Does viscosity index replace the SAE grade?

No. The grade is a defined promise at low and high temperature; the index describes the curve between those points. Two 5W-30 oils can carry different indexes and behave differently in between.

Why do some synthetic oils quote indexes above 150?

Because Group III and PAO base oils are naturally flat and formulators add polymer on top. Above that range the figure reflects a specific base oil choice, worth paying for only where the application needs it.

Can viscosity index be measured on a used oil sample?

It can be calculated and is useful mainly as a trend. A large drop between fresh and used oil usually points to shear or contamination rather than a mislabelled product.

References and Further Reading

The grade system is explained in SAE viscosity grades explained, and the high-shear number that works alongside the index in evaluating HTHS viscosity. The shear question is in shear stability in engine oil, and the base oil side in what Group III base oil is.