HTHS stands for high-temperature high-shear viscosity, and it is the closest laboratory stand-in for the oil film inside a loaded bearing at operating temperature. It is measured at 150 degrees Celsius under a defined shear rate, which is deliberately severe: hot enough to thin the oil, and sheared hard enough to strip out the viscosity that comes from polymer additives. Two oils labelled 5W-30 can sit at very different HTHS values, and that difference is what separates an engine that lasts from one that wears.
A grade tells you what the oil measures in a cold cranking test and in a low-shear kinematic test at 100 degrees. It says nothing about what remains when the oil is hot and being worked. HTHS is the number that answers that question.
The oil is held at 150 degrees Celsius and forced through a narrow gap at a shear rate of roughly one million reciprocal seconds, which is in the range seen in a loaded journal bearing. Because the oil is hot, the base oil itself thins; because it is sheared hard, the viscosity index improver molecules align and contribute less. What remains is the effective viscosity under the conditions that matter. The practical decision path is set out in evaluating HTHS before buying.
- HTHS is measured, not calculated from the grade. Two 5W-30 oils can differ by 0.6 millipascal seconds.
- The shear rate is high enough that temporary polymer thickening largely disappears from the reading.
- The result is a film-thickness proxy: higher HTHS means a thicker film under load, at some cost in pumping loss.
SAE J300 sets minimum HTHS values by grade rather than by product. The 20 grades sit at 2.6, the 30 grades at 2.9, and the 40 grades at 3.5 millipascal seconds, with a higher floor for some 0W and 5W 40 variants. ACEA then layers its own floors: C2 requires 2.9, C3 and C4 require 3.5. An oil can therefore satisfy its grade and still be at the bottom of the range the OEM approval expects.
| Condition or requirement | What a low HTHS implies | What a high HTHS implies | Why |
|---|---|---|---|
| Fuel economy is the priority | Better | Worse | Less pumping and shear loss in the bearing |
| Sustained high load or towing | Riskier | Safer | Film thickness under load is what protects the bearing |
| Very hot ambient or hot sump | Riskier | Safer | Oil thins further as temperature rises |
| Cold climate, short trips | Better | Worse | Lower viscosity helps flow at start-up |
| OEM specifies C3 or C4 | Not allowed | Required | The approval floor is 3.5 |
| OEM specifies C2 or a 20 grade | Required | Not allowed | The approval was written around lower HTHS |
| Older engine, worn clearances | Riskier | Safer | Worn bearings need a thicker film to stay separated |
The gap between grade and HTHS is where mistakes happen. A 5W-30 built on a Group III base with a modest polymer dose may reach 3.2; a 5W-30 built to a European low-SAPS approval will sit at 3.5 or above. Both are 5W-30 on the shelf, and only one satisfies a C3 engine. This is why the approval code, not the grade, belongs at the top of the specification.
The same logic explains why low-viscosity oils are not automatically better. A 0W-20 at 2.7 saves fuel in an engine designed for it, and wears a bearing in an engine designed for 3.5. The film strength question underneath is covered in oil film strength, and how polymers behave over time is covered in shear stability.
Ask for the measured HTHS value on the batch COA, not the grade. If the supplier cannot supply it, the specification sheet limit is the next best evidence, and the absence of both is a reason to look elsewhere. Also ask which method was used, because the three standard methods do not agree to the last decimal.
- Ask for the measured HTHS at 150 degrees, with the test method named.
- Ask for the ACEA sequence and OEM approval the product is built to, since those set the floor.
- Ask for the base oil group and the polymer type, which explain how the number was reached.
For distributors, the practical consequence is that a low-HTHS line and a high-HTHS line are different products with different customers. A fuel-economy buyer wants the first; a fleet running loaded trucks in hot weather wants the second. Selling one as the other is a claim that shows up in warranty claims. Where the low-viscosity range fits is explained in wholesale low-viscosity oil.
If-then: if the OEM approval is C3 or C4, then require HTHS of 3.5 or above and get it on the COA. If the approval is C2 or a 20 grade, then a 3.5 oil is the wrong product despite looking safer. If the fleet runs hot and loaded, then treat HTHS as a purchase criterion equal to price. If the COA omits HTHS, then ask for the specification limit and the test method before quoting.
Need HTHS evidence on a batch rather than a claim on a label? Send the grade and the approval code, and we will return the measured values with the test method on the COA.
Is higher HTHS always better?
No. Higher HTHS protects better under load and costs fuel economy. The right value is the one the OEM approval was written around, not the highest number available.
Can two oils of the same grade have different HTHS?
Yes, often by 0.5 millipascal seconds or more. The grade sets a kinematic range at 100 degrees; HTHS is measured separately at 150 degrees under shear.
Does HTHS change in service?
The measured value falls as the viscosity index improver is sheared and the oil oxidises. That is why used-oil analysis is compared against the fresh value, not against the grade.
