API CK-4 vs CI-4 Diesel Engine Oil: Which Should You Choose?
Engine Oil Insights & Industry Updates

API CK-4 vs CI-4 Diesel Engine Oil: Which Should You Choose?

CI-4 and CK-4 are both heavy-duty diesel categories, and both still appear on drums today. CI-4 arrived in 2002 for engines with cooled exhaust gas recirculation. CK-4 arrived in 2016 with tighter limits on oxidation, aeration, shear and elastomer compatibility, and it was written for engines running hotter with tighter emission controls. Choosing between them is a question about the engine, not about which letter is newer.

The confusion is understandable, because a CK-4 oil is usually backward compatible. That does not mean every drum is licensed as CI-4, and it does not mean an old engine needs the newer category.

CI-4 was designed around soot. Cooled EGR put more soot into the oil and raised the acid load, so CI-4 emphasized soot dispersancy and TBN retention. CK-4 kept that and added limits that CI-4 never had: oxidation stability at high temperature, resistance to aeration and foaming under sustained load, shear stability through the injector and pump, and elastomer compatibility with modern seals.

  • Oxidation stability: CK-4 resists thickening at high sump temperature, which matters for engines running long drain intervals in hot climates.
  • Aeration control: less air entrainment means a more stable oil film and less cavitation in the pump and bearings.
  • Shear stability: the oil holds its viscosity through high-pressure pumps, so a 10W-30 stays a 10W-30 in service.
  • Elastomer compatibility: seals are tested against the oil, which reduces leaks and swell problems in newer engines.
  • Soot handling at higher levels: CK-4 carries the CI-4 soot requirement forward rather than replacing it.

FA-4 was released alongside CK-4 and is not interchangeable with it. FA-4 oils sit at a lower HTHS, usually in 10W-30, for specific modern engines designed around fuel economy. Putting FA-4 into an engine that specifies CK-4 is a film-thickness decision made by the wrong person.

Engine or duty conditionPoints to CI-4Points to CK-4Note
Pre-2007 engine, no DPF or SCRYesAcceptable if licensedCI-4 is often the cheaper fit for the actual requirement
2007 to 2016 engine with cooled EGRYesYes, usually backward compatibleCheck the licence, not just the label
2017 or newer engine with SCR and DPFNoYesFollow the OEM approval, often CK-4 or an OEM-specific spec
Warranty still activeOnly if approvedOnly if approvedThe manual decides, not the price
High-sulphur fuel in an old engineYes, with a TBN reserveYes, but confirm TBNAcid load is the deciding factor
Long drain interval in hot ambientWeakerYesCK-4 oxidation and aeration limits are the difference
Mixed fleet spanning both erasKeep as a secondary SKUPrimary SKUOne modern oil can cover more of the fleet

Two practical notes sit under the table. First, backward compatibility is a licensing question. API allows a CK-4 oil to also carry CI-4 if it meets both, and many do, but the drum has to say so. A buyer who assumes otherwise has no claim if the oil was never licensed for the older category. Second, price is not the only variable: an old engine with high-sulphur fuel needs TBN, and a modern low-ash oil may not carry enough of it. Where to source that category is covered in sourcing diesel engine oil from China.

The most common error is treating CK-4 as a strict upgrade that can be poured into anything. Backward compatibility is real for most engines, but it is conditional: the oil must be licensed for the older category and the engine must still get the viscosity and TBN it needs. The reverse error is keeping a fleet on CI-4 when the newer units in the same yard were designed for CK-4. How to vet the blender behind the drum is covered in evaluating a diesel engine oil supplier.

  • Read the API licence and the label together. The donut shows the category; the licence record shows what it is actually registered for.
  • Match viscosity to the duty. A 15W-40 CK-4 and a 10W-30 CK-4 behave differently in the same engine.
  • Check TBN against fuel sulphur. A low-TBN modern oil in an old engine on high-sulphur fuel will run out of acid neutralisation before the drain interval ends.

For a distributor, the stocking answer is usually one modern CK-4 in the main viscosity plus one CI-4 for the older end, with the split set by the fleet count. Carrying both is not waste if both are sold; carrying both because the catalogue offered them is.

If-then: if the engine is 2017 or newer, then CK-4 or the OEM approval, without debate. If the engine predates 2007 and runs on high-sulphur fuel, then CI-4 with a real TBN reserve is the fit. If the fleet spans both eras, then let CK-4 carry the modern end and keep CI-4 only for the volume that needs it. If the drum claims CK-4 and the buyer needs CI-4 cover, then check the licence before the container ships.

Buying for a mixed-age diesel fleet and unsure how much CK-4 and how much CI-4 to load? Send the engine years, the fuel sulphur level and the drain interval, and we will return a grade and category split with the licence evidence for each.

Is CK-4 better than CI-4?

CK-4 is newer and has stricter limits on oxidation, aeration, shear and seal compatibility. For an old engine on high-sulphur fuel, CI-4 with adequate TBN can serve better.

Can I use CK-4 where CI-4 is specified?

Usually yes, if the oil is also licensed for CI-4 and the viscosity and TBN match the engine’s needs. Check the licence, not only the label.

What is the difference between CK-4 and FA-4?

FA-4 is a lower-HTHS category for specific modern engines that were designed for it. It is not a replacement for CK-4 and should not be used where CK-4 is specified.

References and Further Reading