The 5W in front of both grades is the cold-end promise, and it is identical. The difference sits after the W: a 30 and a 40 are different viscosity bands at 100 degrees Celsius, and the engine was designed around one of them. Asking which is better without naming the engine is like asking which shoe size is better.
The market still treats 5W-40 as the upgrade and 5W-30 as the economy option. That is backwards in a modern engine and sideways in an old one. What matters is the OEM approval, the bearing clearance, the load profile and the ambient range, in that order.
SAE J300 puts the 30 grade between 9.3 and 12.5 mm squared per second at 100 degrees Celsius, and the 40 grade between 12.5 and 16.3. Both must meet a low-temperature pumping limit set by the 5W prefix. So a 5W-30 and a 5W-40 behave similarly on a cold morning and diverge once the engine is hot and loaded. HTHS is the number that decides how far they diverge, and evaluating HTHS before buying walks through it.
| Condition | Points to 5W-30 | Points to 5W-40 | Reason |
|---|---|---|---|
| OEM approval names a 30 grade | Yes | No | The approval is the design intent, not a suggestion |
| OEM approval names a 40 grade | No | Yes | A thinner oil than specified lowers film thickness under load |
| Fuel economy is measured and rewarded | Yes | Second choice | Lower viscosity and HTHS cut pumping and shear losses |
| Sustained heavy load, hot ambient, towing | Risky | Yes | Higher viscosity holds the film when the sump runs hot |
| High-mileage engine with wider clearances | Second choice | Yes | More clearance needs more viscosity to keep the film |
| Cold climate with short runs | Yes | Acceptable | Both start at 5W; the 30 flows slightly faster and warms sooner |
| Turbocharged direct injection with tight clearances | Yes, if approved | Only if approved | Oil flow through the bearings and the turbo feed matters |
Two caveats sit under that table. Viscosity grade is a band and HTHS is a floor, so a 5W-30 built to a high-HTHS approval can hold a film better than a cheap 5W-40. And a 5W-40 is not automatically a better protectant; thickness without flow is its own failure mode. The base oil side of the same trade-off is covered in synthetic versus mineral versus semi-synthetic.
In engines designed after roughly 2010, clearances tightened, oil pumps were sized for thinner oil, and variable valve systems depend on fast flow at start. The OEM approvals written for those engines usually name a 30 grade, often with a specific HTHS floor and a low-SAPS chemistry.
- Fuel economy: the thinner oil costs less energy to pump and shear, and the gain is measurable in a fleet that tracks liters per 100 kilometers.
- Cold start and short runs: faster flow to the valvetrain and the turbo feed, which matters in city duty and in winter.
- After-treatment compatibility: many low-SAPS approvals are built around a 30 grade, so the grade and the chemistry travel together.
- Heat removal: thinner oil moves more volume through the cooler and the bearing gallery at the same pressure.
A 40 grade earns its place where the oil is asked to hold a film under sustained load and high sump temperature: loaded trucks in a hot climate, older engines with wider clearances, industrial and agricultural engines that run at rated load for hours, and any engine whose manual names a 40.
- High ambient and sustained load: the viscosity at 100 degrees is higher, so the film is thicker when the bearing is hottest.
- Older engines: wear opens clearances, and a thicker oil compensates for the oil the engine can no longer hold.
- Mixed fleets with an OEM approval that names 40: keeping one grade for the fleet beats carrying two and mixing them up.
Start from the manual, then from the duty cycle, then from the climate. If the manual names an approval, that approval decides the grade. If it offers a range, choose the upper end for sustained load and the lower end for fuel economy and cold starts. If it names nothing, use the engine family and the ambient range, and write the assumption down.
- List the engine families in the fleet and the approval code for each, not the grade the last supplier sold.
- Ask what the vehicles actually do: motorway kilometers, urban stop-start, loaded grades, or stationary running on a generator.
- Check the oil consumption history. A sudden rise is a mechanical signal, and a thicker grade only hides it.
- Keep the number of grades small. Two grades that cover the fleet beat four that confuse the workshop.
If-then: if the OEM approval names a grade, then buy that grade and stop debating. If the engine is old and burns oil, then a 40 may slow the consumption but the cause is mechanical. If the fleet runs loaded in a hot climate, then a 40 with a real HTHS number is the safer default. If the fleet is modern, urban and fuel-cost sensitive, then a 30 with the right approval pays for itself.
Comparing a 5W-30 and a 5W-40 quotation for the same fleet? Send the engine families and the approval codes, and we will tell you which grade the fleet can legally and safely run, and what the other one costs in fuel and wear.
Is 5W-40 better than 5W-30?
No. It is thicker at operating temperature. That helps under load and in worn engines, and costs fuel economy and cold flow. The engine’s approval decides which one it was built for.
Can I switch from 5W-40 to 5W-30?
Only if the OEM approval allows the 30 grade and the engine is in good condition. On a high-mileage engine with wide clearances, the switch can raise oil consumption and lower oil pressure.
Does a higher viscosity always protect better?
No. Protection depends on flow as well as film thickness. Too thick an oil can starve a bearing at start and run hotter because it moves less volume through the cooler.
